Athena Head Gasket MLS for Ford Galaxy I / Mercedes Benz V-Class / VW Golf / Passat / Sharan 1.65mm 83mm 338321R

ATHENA (MLS) Multi Layer Gasket

Material

ATHENA MLS gaskets feature a combination of 3 to 5 layers made of different types of raw materials.

Outer and inner layers combination is designed to perform at higher compression levels than stock configuration and type of steels that are used may vary upon the engine requirements.

Athena MLS gaskets provide an even torque load across the sealing surface to compensate any type of bore distortion.

Athena MLS gasket is the best solution for both aluminum heads to cast iron blocks and aluminum heads to aluminum blocks.

Manufacturing Process

Athena New Design MLS Head Gaskets are made from high grade 301 stainless steel full hard material.

Each layer is individually formed using a state-of-the-art laser cutting and embossed with an optimized formation process.

2 head gasket layers go through a stress relieving process to significantly reduce embossment forming induced stress.

Proprietary two-part polymer coating is applied after the stress relieving process and ensures uniform coverage of the outer layers providing no break in the coating.This process ensures the micro seal of engine coolant/oil fluids.

Athena MLS gaskets are tested and analyzed on Engine Dynos and endurance performances.

Gas Stopper Technology

Gas stopper technology is a key design factor of racing MLS head gaskets. The stainless-steel stopper layer features a state of the art “active fold”. which delivers a high-pressure seal around the cylinder bore when tightening the cylinder head. Gas stopper is located around the combustion chamber. allowing cylinder head and engine block to clamp tighter and preventing gases to leak out of the combustion chamber.

This also avoids component distortion by means of a quicker equalization of the various components’ temperature.

Benefits

Superior sealing properties under high pressure conditions

Higher elasticity and constant load resistance

Optimized load balance

Improved engine performance

Longer durability

Proprietary Coating Technology

 

Our two-part polymer coating is applied after the stress relieving process and ensures uniform coverage of the outer layers providing no break in the coating. This process ensures the micro seal of engine coolant/oil fluids and meets the demands of a variety of harsh environments.

The first layer is a high temperature compound that will conform to fill engine block deck surface and cylinder head surface irregularities. (Typical MLS head gaskets require a surface finish of 30 Ra. while Athena’s will seal surface finishes up to 60 Ra).

The second layer itself releases easily and will not stick to mating surfaces when disassembling the engine.”

Fits to :

FORD AAA 2792cc 128kw
FORD AMY 2792cc 128kw
FORD GALAXY I (WGR)2.8 i V6 2792cc 128kw
FORD GALAXY I (WGR)2.8 i V6 4x4 2792cc 128kw
MERCEDES-BENZ M 104.900 2792cc 128kw
MERCEDES-BENZ V-CLASS (638/2)V 280 (638.244, 638.294) 2792cc 128kw
VW AAA 2792cc 120kw
VW AES 2792cc 103kw
VW AMY 2792cc 128kw
VW CALIFORNIA T4 Camper (7DJ, 7DK, 70J)2.8 VR6 2792cc 103kw
VW CORRADO (53I)2.8 VR6 2792cc 128kw
VW GOLF III (1H1)2.8 VR6 2792cc 128kw
VW PASSAT B3/B4 (3A2, 35I)2.8 VR6 2792cc 128kw
VW PASSAT B3/B4 Variant (3A5, 35I)2.8 VR6 2792cc 128kw
VW SHARAN (7M8, 7M9, 7M6)2.8 VR6 2792cc 128kw
VW SHARAN (7M8, 7M9, 7M6)2.8 VR6 Syncro 2792cc 128kw
VW SHARAN VAN (7M_)2.8 VR6 (7M8) 2792cc 128kw
VW TRANSPORTER T4 Bus (70B, 70C, 7DB, 7DK, 70J, 70K, 7DC, 7DJ) | TRANSPORTER / CARAVELLE2.8 VR 6 2792cc 103kw
VW TRANSPORTER T4 Platform/Chassis (70E, 70L, 70M, 7DE, 7DL, 7D2.8 2792cc 103kw
VW TRANSPORTER T4 Van (70A, 70H, 7DA, 7DH)2.8 VR6 2792cc 103kw
VW VENTO (1H2)2.8 VR6 2792cc 128kw
VW ABV 2861cc 135kw
VW CORRADO (53I)2.9 VR6 2861cc 140kw
VW GOLF III (1H1)2.9 VR6 Syncro (1HX1) 2861cc 140kw
VW GOLF III Variant (1H5)2.9 VR6 Syncro 2861cc 140kw
VW PASSAT B3/B4 Variant (3A5, 35I)2.9 VR6 Syncro 2861cc 135kw